Coleman Air

Enphase M190, M210 Cable & Solar Junction Box, Seal, 1" conduit nipple/coupling

Specially designed for DIY solar panel installations.

This junction box is designed to sit on the roof itself, often under a solar panel.

It is ready to go, with 1" conduit nipple and compling included.

The wiring from the solar panels enters the bottom of the junction box and is routed through to the back of the box,
through the roof, and on to the inverter, disconnect or sub-panel. You can of course use the box for multiple strings.

The back of the junction box has a 1" soft rubber pad that provides a perfect seal on most all roofs.

Please see the picture of the box as it is installed.

PRODUCT OVERVIEW

For use in Enphase solar installation,with M190 or M210 Micro-Inverters.
Pre-drilled holes on the back of the junction box and rubber pad.
Rubber pad is soft and compressible, forming to minor to moderate roof and shingle irregularities.
Self sealing, soft rubber pads, minimize or elevate the use of any type of sealant.
Extremely weather resistant.
Unique design -- Super quick installations, just drill out a hole in the roof for the coupling and screw the junction box down.
Can be used on wood, shingle and composite roofs as well.

Also Included -- Enphase Energy AC Interconnect Cable 6 Feet. Part number ECWP-6

This cable is the same cable found in the Enphase part number EKIT-01-001 Install Kit.

New, never used. Cable for the Enphase system Inverters. This is the twist lock connector type, not the lines that go to the solar panel.

6ft cable for Enphase M190 or M210 Microinverter systems that connects the trunk lines to the AC junction box.

This item packaging has the part number as 860-00006 REV 03, The actual wire has the part number 840-00021 REV 03 1110. The Enphase part number is ECWP-6
It is possible that these were externally sourced by Enphase.

Please be certain this is the correct cable you need.

* Note: These are brand new unused cables. I am selling these at a great discount.

This item consists of
1) 6X6X4 Wiegmann NEMA 3R outdoor enclosure (junction box), with lockable lid. - UL Listed
1) Rubber, self sealing pad (This pad compresses and seals against moisture when screwed down to the roof)
2) 1" Galvanized lock nuts
1) 1" x 2" Galvanized Conduit Nipple
1) 1" Galvanized Conduit Coupling
1) Enphase M190/M210 Cable - Part number ECWP-6

Please note. Any Unistrut channel, inverters, tools and/or solar panels shown in the photo(s) are not included, only the exact items specified above.

Precision cut on our Waterjet cutter in Coleman Texas, U.S.A

Perfect for DIY Solar racking!!

Shipping And Returns

Our shipping charges are basically what it cost us to ship. International shipping rates via the USPS for this weight are much higher than you might expect. Please click HERE to view just how much these charges are, and you will see that our rates are just what it cost. We would charge less, if it cost us less.
Due to major delays in customs, we no longer ship to Italy.
To our International customers. We cannot misrepresent the price of the products being shipped to you. You are responsible for any and all tariffs, duties or import fees imposed by your country or customs.
Returned items must be in their original condition and fully resalable. Returns may incur a 20% restocking fee. Damages that occur during return transit will be liable to the buyer. Buyer is responsible for all tariffs, customs fees, VATs.

By popular request, here are a few documents that show just how all of these components tie together.

The Big Picture

Three phase turbine wiring diagram

Frequently asked questions. (FAQ)

The Basics And Beyond

If you have any questions, please do not hesitate to ask, we are happy to help.

Thanks For Looking!

Coleman Air -- Empowering Innovation

Wind and Solar Controllers, Electronics, Hardware & Accessories perfect for the DIY'er.

Empowering Innovation